Connecting the world to reliable power
Tool
The alternator selection checklist
Everything to settle before an alternator can be ordered, and why each one changes the machine. This is the page to come to when you are not sure what to ask us.
What this page is for
An alternator is specified by conditions, not by a model number. The same machine can be right for one project and wrong for another, and the difference is almost never the size. It is the duty, the environment, the mounting and the protection.
The list below is the full set. Every other page in this section quotes the part of it that applies to that page, and we work through it with you in the quotation.
Nothing here needs a figure to be useful. Where a number would change the answer, the reason it changes is given instead.
The checklist
The machine
What the alternator has to do, before anything else is decided.
- How big is the machine?The rating in kVA sets the size of the winding and the frame it is built on. This is the first condition in every enquiry, and we ask for it separately from the load.Changes: The frame, the windings, the weight and the price.
- What does the load actually consume?The load in kW is your side of the requirement. The two numbers are close enough to look interchangeable and different enough to cause expensive mistakes.Changes: Whether the machine is the right size for the load it actually carries.
- Is it working continuously, or standing by?A machine that runs all day is held to a different duty from one that starts when the grid fails and runs until it is back. The duty decides how the machine is built and how it is rated.Changes: The rating basis, the insulation margin and the quotation.
- Does it run in parallel with anything?Working with another set, or with the network, changes what the control arrangement has to do and what it has to be told.Changes: The excitation arrangement and the paralleling equipment.
- Is it single phase or three phase?Some machines can be rewired, some are ordered as a single phase winding, and the two are not the same decision.Changes: Whether the machine is rewired or ordered differently.
The site
Where the machine will work, and what that does to it.
- How hot is it where the machine sits?A machine is rated for an ambient temperature. Above that reference the available output falls, and the amount depends on how far above it you are.Changes: The rating, and whether an external control arrangement is needed.
- How high above sea level is it?Air thins with altitude. Less cooling air means less heat can be moved, and the available output falls with it.Changes: The rating.
- Is the machine indoors, in a canopy, or in a container?The enclosure decides the cooling path and how much of the machine the air actually reaches.Changes: The cooling arrangement and the enclosure.
- Is there dust, salt, or monsoon in the air?Filtration on the air path is not free. Screens and filters protect the machine and cost it output, and corrosion protection has to be specified rather than assumed.Changes: The filtration, the coating and the rating.
The grid and the load
The electricity the machine has to match, and what it is going to feed.
- What frequency does the grid run at?The frequency follows the grid and not your preference. It decides the speed of the prime mover and the number of poles in the machine.Changes: The winding, and the engine it is matched to.
- What voltage arrangement does the site run on?The standard arrangement covers the usual grid voltages. A site that runs on anything else needs a different winding, and that is settled before the order rather than after it.Changes: The winding, and the terminals.
- How much of the load is electronic?Electronic load draws harmonics and steps in a way conventional motor load does not, and it changes how the machine holds voltage through a step.Changes: The excitation arrangement and the winding.
- What power factor does the load run at?The machine is sized by current, not by watts. A load that draws more current for the same useful power needs a bigger machine.Changes: The rating.
The engine and the coupling
How the machine is attached to what drives it.
- Is the alternator bolted to the engine, or is it driven from outside?The flange-mounted arrangement takes the alignment load itself and sits inside the set. The bracket-mounted arrangement stands on its own bearings and carries the drive load, which lets it be coupled to a prime mover that is not a standard engine.Changes: The whole mechanical arrangement.
- Which way does the engine turn?Rotation direction is fixed in the design. Some sizes can be built either way and some cannot, and the ones that cannot may not be reconfigured without losing output.Changes: Whether the machine can be supplied for that rotation, and what it costs.
- What speed does the engine run at?The speed and the number of poles together fix the frequency the machine produces.Changes: The machine that has to be quoted.
The order
What has to be settled for the shipment itself.
- How many, and are they for one site?Quantity changes the price, and a quantity split across sites or across deliveries changes the shipping plan.Changes: The price and the delivery plan.
- Where does it go, and on what terms?The destination and the trade term decide what is included, what is not, and who carries the risk at each point.Changes: The commercial terms, the documents and the freight.
- When does it have to be on site?A delivery date constrains the production slot, and it is worth knowing early rather than late.Changes: The production plan and the availability we can offer.
How we use it
Six of these are worth settling before you write to us, and all of them are settled before anything is ordered. The ones that change the machine most are the duty, the ambient temperature and the mounting, because each of them decides what the machine has to be rather than what it has to do.
When you send a requirement, the useful content is short: the machine rating, the running load, the duty, the frequency and the site conditions. We will ask for the rest as well, because the rest is what stops a machine arriving that cannot do the job.